WAVLINK N300 Wireless Access Point With PoE Powered, WAN/LAN Port, Wi - Fi Extender Long Range With AP/Router/Repeater Modes, 2x7 DBi Directional Antennas
White
$27.12
Skip to product information
This wireless access point is PoE powered with an operating voltage of ≤36V, allowing for power delivery over a single cable.
The device supports AP, Router, and Repeater modes, providing networking solutions for various environments.
Equipped with 2x7 dBi directional antennas, this access point extends Wi-Fi coverage for wireless connections.
Operating on the 2.4GHz frequency band, this device provides Wi-Fi connectivity for commercial, family, and gaming usage.
WAVLINK N300 Wireless Access Point With PoE Powered, WAN/LAN Port, Wi - Fi Extender Long Range With AP/Router/Repeater Modes, 2x7 DBi Directional Antennas
$27.12
The device supports AP, Router, and Repeater modes, providing networking solutions for various environments.
Equipped with 2x7 dBi directional antennas, this access point extends Wi-Fi coverage for wireless connections.
Operating on the 2.4GHz frequency band, this device provides Wi-Fi connectivity for commercial, family, and gaming usage.
Multiple Working Modes: It supports four working modes. The repeater mode extends the Wi-Fi coverage of an existing wireless network. Router mode creates an instant private wireless network, enabling multiple devices to share it. AP mode converts a wired network to a wireless one. AP+Repeater mode extends the range of a wireless network by using a repeater to amplify and relay the signal from an access point.
Power Over Ethernet: Integrated Power over Ethernet (PoE) enables power and network data connections to be consolidated into a single RJ-45 cable, allowing installation in areas without power outlets. It is equipped with passive PoE and also supports active PoE. You can use and connect your own active switch.
Access Point: It has a maximum coverage range of 150 meters, supports up to 32 devices, and provides 2.4GHz, 300Mbps, high-speed, and 100M Ethernet ports. Simple settings enable wireless optimization to improve the quality and effectiveness of link transmission. (Coverage may vary based on the actual environment.)
Single-Band Range Extender: Powered by 802.11n Wi-Fi technology, you can enhance your existing wireless coverage even in single-band range, providing speeds of up to 300Mbps on the 2.4GHz band. This allows you to enjoy high-speed downloading of your games, videos, and other files even in public areas.
WAVLINK 300Mbps Access Point The WAVLINK HighPower Wi-Fi AP/Repeater/Extender is mainly used for providing free Wi-Fi service in large areas such as factories, communities, streets, etc. The AP/Repeater/Extender can take an existing 2.4GHz wireless signal, repeat it, and extend it to a longer range where it is too far away for the router or access point to reach. And it can support 2.4G transmission speeds of up to 300 Mbps. It has two external antennas.
7dBi Omni Directional Antenna The high-gain antenna panel has two built-in 7-dBi omni directional antennas, which are designed to strengthen the WiFi signal in one direction and make it more concentrated. And WiFi coverage in a specific direction is farther than omnidirectional antennas.
Default Parameters 2.4G SSID: WAVLINK-N XXXX Default IP: 192.168.10.1 Default Password: admin
How to Install Antennas and Ethernet Cable? 1) Pass the RJ45 cable through the spiral cover. 2) Pass the RJ45 cable through the rubber seal. 3) Pass the RJ45 cable through the holder. 4) Connect the RJ45 cable to the RJ45 port. 5) Spin the 2.4G antenna into the 2.4G external RP-SMA connector. 6) Tighten to secure the holder. 7) Insert the rubber seal into the holder. 8) Secure the spiral cover by screwing it on.
Installation Steps for the Device 1) Fasten the main body holder. 2) Plug the device into the holder. 3) Connect one end of an Ethernet cable to the "PoE" port of the PoE converter. 4) Connect one end of another Ethernet cable to the "LAN DATA IN" port of the PoE converter, and connect the other end to a "LAN" port of your router. 5) Plug the Power Adapter into the power outlet. 6) Push the "ON/OFF" button on the PoE converter to power on.
Specification 1.Model: WL-WN570HN2-B 2.Ports: 1 x WAN/LAN 100Mbps 3.Button: 1 x Reset(8s); Status LED: 1 x Power, 1xWAN/LAN, 1 x WiFi , 3 x Signal 4.Power Supply: DC 54V/0.3A Power over Ethernet(Passive), DC 48V Power over Ethernet(Active) 5.Wireless Standard: IEEE 802.11 b/g/n 6.Frequency Band/Speed: 2.4GHz(300Mbps) 7.Antenna: 2 x 7dBi Omni Directional Antennas 8.Wireless Security: WPA-PSK/WPA2-PSK encryption
Features - Easy installation, flexible placement - Supports AP, Router, Range Extender and AP+Repeater modes - Complies with IEEE 802.11 b/g/n standards, wireless speed up to 300Mbps - 2x 7dBi high-gain antennas - Supports WPA/WPA2 (TKIP/AES) Encryption modes - Features 6 LED status indicators
In the Box 1x N300 Outdoor Access Point 2x 7dBi High-gain Antennas 1x RJ-45 Ethernet Cable 1x Power Adapter 1x PoE Converter 1x Main Body Holder 2x Cable Ties 1x Screw Fitting Kit 1x Quick Start Guide